65 Woodworking Tips

65 Woodworking Tips For Every Beginner

These 65 tips that you’ll learn are like simple hacks that’ll take you to the top before you even realize it. 

As there are a lot of things to master in the woodworking world, we’ve got the basic tips for you first. So, let’s have a look at the tips.

Tip 1: Make A Half Pencil

You should break your work pencil from the bottom to the middle. This allows the pencil to run through perfectly when you’re using a template to measure or draw on something.

Tip 2: Keep the Saw Straight 

You see, when you’re holding your saw, don’t keep your finger inside of the grabbing rail, your cuts will be curved for sure.

Tip 3: Use Bench for Blade

You can use your bench for the initial setup on your blade. The taps on the wedge and the blade will be just enough to make it engage-able.

Tip 4: Measure from the Inches

Measuring with the end hook added, makes the measurement inaccurate. So, it’s better to measure from the exact inch from the tape.

Tip 5: Two Nails on a Straight Board

All you need is two nails and a straight board to make any kind of angle shooting boards you want. You just have to place the nails on the board crossly.

Tip 6: Use Rubber Pads

You can place rubber pads under your benches feet because it prevents the feet from sliding around and causing an accident. Works just like sneakers.

Tip 7: Add Copper Down to the Leg Vise

You can try adding a copper down to your leg vise. It’ll surely make it look better, will give you more comfort and easy to move.

Tip 8: Use Sandpaper Eraser

You can make sandpaper erasers work just as well as hooking hoops as they do your bell sanders. 

Tip 9: Slight Radius Blade on Smoother

A slight radius blade on your smoother as it can give you a smoother sensation to the fingers because you won’t feel the undulations.

Tip 10: Skew Your Blade

If you ever think that you need a lower angle blade, skew the blade a little bit and it’ll get the job done.

Tip 11: Say Yes to Block Plane

A block plane can be a lot more comfortable than the number three smoother. Give it a run. 

Tip 12: Always Use a Brush

You should ALWAYS use a brush to clear away the shavings. Because sharp equipment might create an event that you’ll not be ready for.

Tip 13: Short Boards or Jointer

The short-boards are so smooth that it might as well be a jointer. Sounds crazy but it can really be used as a jointer.

Tip 14: Find the Sandpaper

You can store sandpapers onto a wooden wall by using a Velcro so that you can find them right when you need them.

Tip 15: Use Magnets

Use large magnets to keep a hold on your small handy things. Like screwdrivers or screws.

Tip 16: Quick Mixing Surface

If you ever need to mix something, you’ll need a surface to mix it on. Use tapes to create a mixing surface on the wood and then mix your stuff in that place.

Tip 17: Use a Stain Sprayer

Just use an empty bottle to make a stain sprayer. It makes your work less hard and fast.

Tip 18: Protect Your Table Saw

You can rub on a coat of paste wax to protect your table saw top. Even if you drip glue on the surface anymore it won’t stick and keeps it clean.

Tip 19: Safety When Taking Care of Small Parts

You should attach the small parts on 2×2 with a dowel screw. Keeps the part straight and keeps you safe too.

Tip 20: Folding Workbench

You can just use hinges with two wood parts that’ll make the fold-able workbench and give you more mobility. 

Tip 21: Clean the Dust Easily

You can clean the dust easily as the leaf blower is the best cleaner device to be ever invented. 

Tip 22: Don’t Hurt Your Palm

Make sure that you don’t support a chisel or screwdriver back with the center of your palm and start pushing with it. That’s where all your nerves are at and it can cause serious damage.

Tip 23: Use a Tungsten Burnisher

A tungsten burnisher will make you feel like a superman. Because it is able to bend even modern steel. 

Tip 24: Use a Modern Hansel

A modern hansel is an engineering marvel. The handles are designed to fit your hand perfectly and add functionality. Makes starting a cut a lot easier for you.

Tip 25: Sharpen Chisel on a Stroke

Sharpening a chisel on a stroke often will maintain the edge a lot longer and make them a lot more useful than sharpening them on the stones. 

Tip 26: Focus on Body Alignment

It’s very essential that you make sure that your body alignment is correct for your own safety. 

Tip 27: Rubber and Hard Side Hammers

You should grab one of those rubber and hard side hammers. Use the rubber on the wood and the hard side on the blades. 

Tip 28: Wax Everywhere

Use wax wherever you can. It makes the surfaces easier for your work and makes it smoother for the cuts.

Tip 29: Reduce the Blade Drift

To reduce the blade drift as much as possible, you need to center your guards on top of the crown of your wheel instead of the center of the blade. 

Tip 30: Simple Sandpaper Cutter

You can try slipping a washer behind the blade at each of the mounting holes so a sheet of sandpaper can easily slide in behind the table. 

Tip 31: Your Glue is Still Good

Just add a drop or two of vinegar in your glue bottle or jar. It’ll make the glue look and act like new.

Tip 32: Easy Miter Saw Stop

You just need to clamp a jumbo clip to your fence and use a ¼ inches thick wood scrap pinch in the clip as a stop. It takes only a second.

Tip 33: Tape to the Rescue

Use the painter’s tape as clamps. Set the pieces and tape them edge to edge. You can then flip the pieces over so the leveled edges are facing up and glue them together. Tape two edges together and let it set.

Tip 34: Flag the Wood

If you’re transporting long lengths wood from the lumberyard, make sure that you’re attaching a warning flag with a spring clamp in the back of your vehicle.

Tip 35: Hole Saw Drum Sander 

You can use sandpaper and attach it with a round piece of wood. Then, attach that to the drill and there you have a sander which can sand any hole areas related to its size.

Tip 36: Mark Your Sanding Area

Make sure to mark the areas that need sanding in the future. You can use your work pencil to mark the areas for the future.

Tip 37: Make a Super-Strong Sandpaper

You can use some duct tape nicely behind the sandpaper. It makes the sandpaper more flexible. You can sand places where you weren’t able to before. 

Tip 38: Socket Sander

Concave moldings can be really hard to sand. You just need to find the right fit socket and then use sandpaper with it to sand the place smoothly.

Tip 39: Duct Tape to Rescue Again

If you don’t want friction burns, put on your gloves, and wrap painter’s tape around it. Remember to put the sticky side out. Your hand is not going to slip anymore.

Tip 40: Build a Stain Index

You can just take the section off boards of your favorite woods into squares with masking tape, apply the different stains on those, and there you have it.

Tip 41:  Bicycle Tubes or Stretchy Clamps?

You can use old bicycle inner tubes for clamping odd-shaped projects. They work amazingly because of being so stretchy. 

Tip 42: Create a Mixing Block

If you mix a lot of epoxy in small batches, you should try this. You just need to drill 1- ½ inch holes in 2×4 scraps with a Forstner bit. The results are the holes that you need.

Tip 43: Clean Mini Drum Sander

You can refresh the surface of the sanding drum with a pencil eraser. You need to run the tool at low speed and press the eraser into the clogged drum.

Tip 44: Sanding Super Small Parts

You might have noticed the emery boards that are used for filing fingernails. Well, you can use those to sand small parts. You can sand more easily and precisely with it.

Tip 45: Save Your Hole Saw

You can stuff a moist rag in your hole saw. It’ll keep the saw cooler and the teeth sharper. Also, it’ll extend the longevity of the saw. 

Tip 46: Scraps Storage

You can use the concrete forms for scraps storage. Then you can find a piece of wood easily right near your hand when you need it.

Tip 47: Screwdriver to Awl

You can transform an old screwdriver to an awl. You just need to grind the tip into a sharp cone shape on a bench grinder and you’ll have an awl.

Tip 48: Mustard Bottle – New Glue Storage

You can use an old mustard bottle as your glue storage. They won’t clog and they easily reseal between uses. 

Tip 49: Make Your Glue Spreaders

You can use a credit card as a glue spreader. Snip along its wide edge with pinking shears. The shape that is created after that helps you to spread the glue on a surface.

Tip 50: Make a Simple Sanding Block

You can make a sanding block yourself if you need one. You can just attach the sandpaper with a small long block and use it as a sanding block.

Tip 51: Sand Your Own Hands

Sometimes there will be stuff to deal with which is hard to remove. In that case, you can just grab sandpaper and start sanding on your hand.

Tip 52: Quick Miter Fix

If you have a slightly open miter joint, you can just rub the shank of a screwdriver along the miter at a steep angle from both sides of the joint. It’ll look good as new then.

Tip 53: Sanding Station

You can create a sanding station for sanding small items. You need to attach sanding paper to a wooden surface and boom. You have your sanding station.

Tip 54: Fix Dents Quickly

You simply need to soak a washcloth in water and put it on the dented place and iron the spot over the washcloth. You need to do it again and again till the dents rise up to be flush with the rest of the material.

Tip 55: Sanding Pad Replacement

You can use extra foam and attach the foam with contact cement. It works for clamping as well as sticking on sanding squares.

Tip 56: No-Slip Sandpaper

Often sandpapers slip from your hand while sanding. So, you just need to fold the sandpaper and it’ll never slip from your hand again.

Tip 57: Give Life to Old Epoxy

If your epoxy container is crystallized, you can take care of it. You need to set the container in a bowl of hot water. After some time, your epoxy will regain its normal consistency.

Tip 58: Spare Glue Bottles from the Recycling Bin

You just need to fill snap-capped sports water bottles with glue and stick the upside-down in a hunk of 2×6. You wouldn’t need to wait for the glue to run into the neck of the bottle.

Tip 59: Use Stools

Stools make a great work surface for sheet goods. Place them beneath the sheet goods and start cutting.

Tip 60: Keep the Pencil Tip Sharp

Rotating your pencil tip after each pass will keep your tip sharp. It evens out every side of it.

Tip 61: Mark Your Depth

You can use your deck marker, fold over it so that it looks like a flag. It’ll help you know when to stop.

Tip 62: Check Your Rulers

Be sure to check your ruler measurements. Because a lot of time different rulers come from different markets or countries and they might give false readings too.

Tip 63: Chopsticks Makes It Stick

You can take chopsticks and apply glue on stuff using it. It’ll get your job done even if the glue needs to be at a narrow place.

Tip 64: Tap to Clean

If any instrument ever gets dirt, tap it to the table to remove the dirt. You can also use a shoe shining brush to clean too. 

Tip 65: Take Care of Accidental Cuts

You can keep hydrogen peroxide in a bottle and use it in case you get a cut. It’ll instantly stop the bleeding from your cut.

Open